Competition Motorsport
CMS Performance RF1 DOT4 Racing Brake Fluid (500 ml)
from $24.95
CMS Performance RF1 DOT4 622oF Racing Brake Fluid
Buy in bulk and save. Get six bottles and save 15%, or a case of 12 and save a whopping 25%!
The Highest Dry Boiling Point Racing Brake Fluid You Can Buy
CMS Performance RF1 fully synthetic Racing Brake Fluid is formulated to provide the highest performance under racing and track-day conditions, where braking systems operate at very high sustained temperatures. RF1 exceeds all DOT 3 & 4 requirements and is compatible with all DOT 3, 4, and 5.1 fluids. (Not compatible with DOT5 or mineral-based brake fluids.)
There is perhaps no single safety system more important in racing than brakes. And no part of that system is more critical than brake fluid. At Competition Motorsport, we got tired of (and a little nervous) using "racing" brake fluid on the track that didn't live up to its claimed performance.
So we did something about it. Manufactured in partnership with Orthene Chemicals, a British brake fluid supplier to professional race teams in Formula 1, WEC, and many other pro series, CMS Performance RF1 Racing Brake Fluid is formulated to maintain consistent viscosity, lubricity, and compressibility at extreme temperatures and line pressures found in racing, track days, and spirited driving.
Bottom line: you can spend more money, but you can't buy higher-performing racing brake fluid!
CMS Performance RF1 Racing Brake Fluid Specifications:
Typical dry boiling point: 622° F (328° C)
Typical wet boiling point: 399° F (204° C)
Exceeds DOT3 & DOT4 standards
Individual 500 ml (16.7 oz.) bottles
Click Here For The RF1 Product MSDS Sheet
A Note About Brake Fluid Boiling Points
DOT 4 brake fluid like RF1 is hygroscopic, meaning it attracts water over time sitting in your brake lines and reservoir. At high brake temperatures, this water can boil in your car's brake lines, causing the fluid in the lines to become compressible. That's what you feel when you experience brake fade. This is why the "wet" (aged fluid) boiling point of any brake fluid is substantially lower than the "dry" (brand new fluid) boiling point.
Since time is the enemy of brake fluid performance, the best practice is to replace your racing brake fluid before each track event/weekend. At a minimum, flush it with new fluid at least every three months if you're consistently racing and/or driving at track days. A couple bottles of fluid will flush most sports cars or race cars. It ends up being pretty cheap insurance against learning about brake fade the hard way.
Girodisc
Girodisc Pad Spreader GDPS01
$250.00
Girodisc Brake Pad Spreader
This indispensable tool is used by race teams, shops, and enthusiasts alike who have high performance four- and six-piston calipers. The spreader is designed to spread brake pads and pistons in four- and six-piston calipers to facilitate quick replacement of pads and/or rotors in a shop or racing environment.No more screwdrivers, pliers, hammers, or C-clamps! This tool will retract the pistons evenly and all the way back into their bores with one squeeze of the levers. The Girodisc spreader was designed around popular four-piston and six-piston calipers from Brembo, AP Racing, Alcon, and other performance calipers in racing and road use. To help fit in any caliper, the amount of throw is adjustable.Insert the spreading plates one way for wider six-piston calipers, then turn the spreader 90o and use the plate sides for four-piston calipers.The Girodisc Pad Spreader is made from heavy-gauge steel and is powder-coated for durability. The slider is cadmium-plated, and nylon pivot bushings ensure smooth action. The Girodisc Pad Spreader will quickly become an invaluable tool for any race team, shop, or enthusiast who changes pads and rotors with any frequency.
Girodisc
A1-075 Girodisc 2pc Front Brake Rotors
$1,900.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Ferrari 599 GTB with Optional CCM Rotors
The Girodisc system is a direct replacement for the OE disc however a different brake pad with an annulus (pad swept area) of 66mm or less must be used. This is done to keep the rotor weight at a reasonable level. If we manufactured a rotor with the same annulus as the OEM CCM rotors they would be far too heavy.The necessary pad shape is available from both Pagid and PFC. If there is a specific pad compound you're after please contact us directly to provide the correct part numbers.The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from our own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 8 or 10 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by grade 12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed. Sold/priced in pairs
Girodisc
A2-075 Girodisc 2pc Rear Brake Rotors
$1,800.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Ferrari 599 GTB
The Girodisc system is a direct replacement for the OE disc.No modifications are necessary. The disc will bolt directly to the car and work with OE calipers perfectly. The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from our own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.The rotor and hat have a floating mount system, which utilizes 8 or 10 high strength alloy steel drive pins, manufactured by Girodisc in the USA to our own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by grade 12 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.Once the Girodisc system is in place, simply replace the cast iron rotor when needed.
Pagid
Pagid Racing Brake Pads No. 4906
from $497.86
Fits These Vehicles:
Make
Model
Build (Year)
Front
Rear
Chevrolet
Camaro Z28 [ceramic brakes]
15 -
X
Chevrolet
Corvette Brembo [ceramic brakes]
09 -
X
Chevrolet
Corvette C7 Z06 [ceramic brakes]
15 -
X
Dodge
Viper ACR [ceramic brakes]
16 -
X
Ferrari
360 Challenge Stradale [ceramic brakes]
03 - 05
X
Ferrari
430 Challenge [ceramic brakes]
X
Ferrari
430 Scuderia [ceramic brakes]
07 - 10
X
Ferrari
458 Italia [ceramic brakes]
10 - 15
X
Ferrari
599 GTB Fiorano
06 - 12
X
Ferrari
Enzo [ceramic brakes]
02 - 04
X
Ferrari
F430 [ceramic brakes]
05 - 10
X
Ferrari
Several ceramic brakes CCM
X
Lamborghini
Aventador LP700-4 [ceramic brakes]
11 -
X
Lamborghini
Several ceramic brakes
X
RSC 1:
RSC1 is a good street/track compromise for enthusiasts with carbon-ceramic brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
RSC 2:
The Pagid RSC2 is a special race compound for ceramic discs with a high content of fibers in the friction surface. A medium-high friction pad with excellent fade resistance and long pad life, developed for sprint and endurance circuit racing.
RSC 3:
The Pagid RSC3 is a high-friction compound developed for ceramic discs. With a high initial bite, strong fade resistance, and slightly shorter pad life than the RSC2, this is Pagid's more aggressive ceramic-rotor racing pad.
Pagid
Pagid Racing Brake Pads No. 8091
from $684.41
Fits These Vehicles
Make
Model
Build (Year)
Front
Rear
Chevrolet
Camaro Z28 [ceramic brakes]
15 -
X
Chevrolet
Corvette Brembo 6 piston non ceramic
09 -
X
Chevrolet
Corvette Brembo [ceramic brakes]
09 -
X
Chevrolet
Corvette C7 Z06 [ceramic brakes]
15 -
X
Ferrari
430 Challenge [ceramic brakes]
X
Ferrari
430 Scuderia [ceramic brakes]
07 - 10
X
Ferrari
458 Italia [ceramic brakes]
10 - 15
X
Ferrari
599 GTB Fiorano
06 - 12
X
Ferrari
Several ceramic brakes CCM
X
McLaren
570 S [ceramic brakes]
15 -
X
McLaren
650 S [ceramic brakes]
14 -
X
McLaren
675 LT [ceramic brakes]
15 -
X
McLaren
MP4-12C [ceramic brakes]
11 - 14
X
RSL 19:
The PAGID RSL19 (Yellow) is the world-leading endurance brake pad used by most of the winning teams in motorsport. Although designed primarily for endurance racing, many competitors use this material successfully for sprint and short distance races also. RSL19 has also found favor in the growing track day market due to the level of control, good cold performance, long life and low disc wear.
RSC 1:
The Pagid RSC1 is a good street/track compromise for enthusiasts with Carbon-Ceramic Brakes. Used for sprint racing and track days compound with all known types of ceramic brake discs. An ideal combination of cold friction, fade resistance and low thermal oxidation of the disc surface.
RSC 2:
The Pagid RSC2 is a special race compound for ceramic discs with a high content of fibers in the friction surface. A medium-high friction pad with excellent fade resistance and long pad life, developed for sprint and endurance circuit racing.
RSC 3:
The Pagid RSC3 is a high-friction compound developed for ceramic discs. With a high initial bite, strong fade resistance, and slightly shorter pad life than the RSC2, this is Pagid's more aggressive ceramic-rotor racing pad.
Sign Up and Save
Subscribe to our eNewsletter to learn about events near you, great deals, new products and for tips to improve your creator skills.
