Data System Components

AiM Sports AiM Sports Strada Logger GPS Upgrade Kit $1,165.00

Strada Logger, GPS08 Module, And Data Hub Turn Any MX Strada Into a Full Data Logger Receiving and reading data while you are driving is not enough anymore? Then it's time to step your game up with the brand new Strada Logger Kit! This kit includes the Strada Logger, Data Hub and GPS08 Module, the kit will turn any MX Strada into a full-working logger, able to collect data ready to be analized on Race Studio 3 to make you improve your performance, understand whether there are problems or not within your vehicle and much much more. STRADA LOGGER A small SD Card holder that can be connected via CAN bus to your MXG 1.2 Strada, MXP Strada, or MXS 1.2 Strada. (It can also be connected to your MXG 1.2, MXP, or MXS data logger for data back-up and super-fast downloads.) GPS08 MODULE More precise than most of the existing GPS systems, the GPS08 was designed to add to the GPS satellite's signal the Global Navigation Satellite (Glonass) system's signal. With an average of almost twenty satellites working in conjunction, GPS08 guarantees precision and a reliability simply not comparable to other GPS systems. DATA HUB A CAN connection multiplier that works as an interface between all AiM loggers and their peripheral equipments. Just connect the Strada Kit to your AiM MX device and data will be saved on an SD card (not included) up to 32GB. as well as stored in the logger memory. No configuration is needed. The SD card can be removed and replaced even during pit stops, while the car engine is still ON, making it extremely fast to get data during endurance races or long tests when the time in the paddock is really limited. When your session is over, plug your SD Card into your PC and download data into Race Studio 3. The Strada Logger has a front LED that shows its recording/firmware status. Reliable and easy to install, the Strada Kit is just what you need to go from an above average driver to a real race one!

AiM Sports AiM Sports LCU-One Lambda Controller Kit $419.00

AiM Sports LCU-One Lambda Controller Kit LCU-One CAN is the lambda controller unit designed to work exclusively with Bosch LSU 4.9 wideband probes, which are the quickest and most accurate way to analyse exhaust gases and provide a real time parameter related to engine carburetion. Lambda probes can be applied to two- and four-strokes engines, gasoline, diesel, methane or alcohol based fuels. LCU-One CAN communicates with your AiM MXL, MXL2, or MXG/MXS dash; EVO3/EVO4/EVO5 data logger; SoloDL lap timer; or MyChron4/MyChron5 kart dash via CAN. This provides lambda value, air/fuel ratio, probe temperature and diagnostics parameters. An external 12 volt battery is required to supply power to the whole AiM system, and any other AiM expansions. LCU-One CAN is the only AiM Lambda Controller compatible with MyChron5.

AiM Sports AiM Sports 22-Pin Dash Harness $399.95

AiM 22-Pin Dash Harness This 90° harness plugs into the 22-pin connector on either the AiM MXP, MXL2, MXM, MXG, MXS dash, and AiM EVO5 Logger. Several of the advanced functions rely on this harness, which is not included with the standard kit. AiM 22 Pin Auxiliary Harness for MXP, MXG, MXS, MXL2 Dashes Details: Manufacturer: AiM Manufacturer part number: V02573020 Alternate part number: MC-249 Harness Angle: 90° The AiM 22 Pin Auxiliary Harness will provide access to the following functions: Analog sensor channels 5, 6, 7, 8 Digital wheel speed sensor inputs 2, 3, 4 Digital 12v outputs 1, 2 RS232 ECU connection The factory harness that comes with the AiM MXG, MXS, MXL2 allows only 4 inputs. If you would like more inputs then this is your harnessFor use with AiM MXS, MXP, MXL2, MXG, and EVO5 Dash/Loggers. Not compatible with older AiM MXL Pro / MXL Pro05 or AiM EVO series. AiM 22 Pin Auxiliary Harness for MXP, MXG, MXS, MXL2 Dashes Primary use: Adding analog sensors greater than 4. Your factory harness will allow up to 4 analog channels (sensors), this may be (1) Water Temperature, (2) Oil Temperature, (3) Oil Pressure and (4) Brake Pressure. Using the AiM 22 Pin Auxiliary harness you now can add four more analog channels (sensors) like (5) Steering Angle, (6) Throttle Position, (7) Gear Box Temperature, and (8) Differential Temp. Another way we see this cable used is independent shock travel (all corners) or engine oil temperature pre-cooler and oil temperature post-cooler.

AiM Sports AiM Sports GPS09 Module $349.00

AiM Sports GPS09 Module The GPS09 module from AiM further expands the track mapping abilities of AiM data loggers and dash loggers. In addition, the GPS09 allows lap timing (even split times) without the use of trackside beacons, storing data for up to 50 tracks with up to 5 splits per track. The GPS09 can also calculate and log speed, lateral and longitudinal g-forces, and of course vehicle position.The GPS09 is the latest version, boasting a quicker 25 Hz sampling rate (up from 10 Hz) and positional accuracy to less than one foot (down from 2 meters). It also takes full advantage of Race Studio 3's integration of GPS, video, and data. Simple to install: Just connect the CAN cable to your dash and mount the magnetic-backed GPS antenna to your vehicle roof. The GPS unit willl even automatically configure itself during start-up! The GPS09 connects via a 5-pin 712 screw-in conncetor and is compatible with current-generation AiM MXL2/ MXG/MXP/MXS auto dashes, EVO4S/EVO5 data loggers, and SmartyCam HD GP 2.2. Choose a cable length to suit your installation: 1.3m (4 ft) is appropriate for most formula cars and bikes. 4m (13 ft) is long enough for sedans. SmartyCam Note: Only the SmartyCam HD GP 2.2 takes this version. SmartyCam HD, SmartyCam HD GP, and SmartyCam HD 2.1 all require the AiM GPS09B which has a 4-pin connector. MXL / EVO3 / MyChron4 Note: This version is only compatible with the latest-generation loggers; it is not backwards-compatible with the first-gen MXL, the EVO3, or the MyChron4. Solo2/Solo2DL, MXm, and MyChron5 do not use an external GPS module; all GPS functions are internal. COMPATIBILITY GPS08 (five pin): MXL/MXL2, MXG, MXP, MXS, and MXm dashes, SmartyCam GPHD Rev 2.2, EVO3, EVO4S, and EVO5 GPS08B (four pin): SmartyCam GPHD Rev 2.1, SmartyCam GP Rev 2.1 Available in either Standard or Roof-Mount versions.

Add to cart

AiM Sports AiM Sports TC Thermocouple Multiplier Hub $289.99

AiM Sports TC Thermocouple Multiplier Hub The AiM TC Hub allows the simplification of sensor wiring, allowing the various sensors to plug into the hub and just one cable back to the logger. In addition, it will enable you to manage critical engine temperatures.The TC Hub has four temperature inputs labelled TEMP 1, TEMP 2, TEMP 3 and TEMP 4. It communicates with AiM loggers by using a CAN network and supports K Type thermocouples only.Available sensors for the TC Hub include the Exhaust Gas Temperature Sensor (EGT), M5 Water/Oil Temperature Sensor and the M10 Water/Oil Temperature Sensor for cars.AiM thermocouples are all cabled with a male Mignon connector. The TC Hub features a metalic Binder, meaning patch leads are required. The AiM thermocouple patch leads (712 3 pin) are available in 1.5m to 3m lengths and are available in the accessories tab for this product. Key Features : Configurable up to 50Hz per channel Enhance your logger performance Simplify your wiring 5 pin Binder 712 male connector

AiM Sports AiM Sports Channel Expansion Hub $250.00

Aim Sports Channel Expansion Hub This compact CAN device provides virtually endless data acquisition system expansion options. The AiM Sports Channel Expansion Hub adds up to four freely configurable analog (or two digital and two analog) channels without occupying or modifying any of the existing system channels. By using advanced CAN technology, wiring is simplified from four cables into just a single connection, thereby reducing possible and unnecessary points of failure. Using the AiM Sports Data Hub, it's possible to connect to as many Channel Expansion Hubs as needed.

AiM Sports AiM Sports ECU Bridge RS232- CAN Wiring $249.99

AiM ECU Bridge with RS232 / CAN Wiring Connecting to the ECU allows the AiM unit access to data collected by your ECU (RPM, road speed, coolant temperature, and throttle position are typical; many ECUs offer much more information). Works with these AiM displays with a male 5-pin CAN connector: MXG MXS MSM MXL & MXL Pro G-Dash Display Formula Car Wheel Display SmartyCam requires the AiM 7-pin to 5-pin CAN Cable (Part No. MC-542, included with the SmartyCam). The ECU Bridge also features a special port for a USB cable (included) for easy connection to your computer for setup. ECU Bridge is available with CAN/RS232 connection, for direct installation on aftermarket ECUs. ECU Bridge and RPM Bridge are needed whenever engine data are to be visualized on a display or on a SmartyCam HD video, if no recording is required. ECU Bridge is used when the ECU transmits data via OBDII, CAN or RS232. AiM has developed hundreds of different protocols to make compatibility with virtually any ECU possible, stock or aftermarket. ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ECUs on the other side. WIRING DETAILS: CAN protocol for external modules (visors or SmartyCam HD) USB port for PC communication External power 8/18 V

AiM Sports AiM Sports MyChron Expansion Channel Multiplier $249.00

AiM MyChron Expansion The AiM MyChron Expansion is an add-on for the MyChron4 or MyChron5 Kart Racing Data Logging Dash. It plugs into the CAN expansion port on your MyChron dash to expand its capabilities. The Expansion has a single CAN expansion port plus four additional sensor inputs. All four inputs can accept common karting sensors (brake/throttle pedal position, temperature, steering angle, etc.). One of the four inputs can accept a speed sensor instead. Requires an external 12-volt power source such as your kart's battery. The MyChron Expansion channel multiplier improves MyChron5 and MyChron5 2T (and also MyChron4 and MyChron4 2T) performance, thanks to four additional channels and a further CAN bus connector. Through this last connector, the systems can be connected to LCU-One Lambda controller and SmartyCam HD (and to GPS and Data key for MyChron4 systems). Thanks to its specific wirings, MyChron Expansion powers the systems and their peripherals with an external battery, avoiding internal battery consumption. All channels are easily configurable as analog through the system menu to sample data coming from: Exhaust gas valve position sensor (very important to understand at which RPM value the exhaust port opens) Wheel speed sensor: the first input on the left can be configured also as digital input No contact brake pedal position sensor No contact throttle pedal position sensor Brake pressure sensor Water temperature or cylinder head temperature (PT100 thermo-resistor only) Steering angle potentiometer (to highlight over/under steering situations) Brake pedal potentiometer Throttle pedal potentiometer MyChron Expansion is a complete, value-for-money instrument for professional kart analysis. Call us with any questions you have about the MyChron Expansion from AiM Sports!

AiM Sports AiM Sports MXS/MXP 23 Pin Harness $175.00

AiM 23-Pin MXS/MXP Strada Harness This add-on harness plugs into the 23 pin AMP connector on the AiM MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada street dashes to unlock certain dash features. If you don't want to build your own harness, this harness is required in order to use the following features: Analog input channels (8) Digital wheel speed channel (1) RPM input Digital output CAN2 stream input Manufacturer: AiM Manufacturer part number: V02573220 For use with AiM MXS 1.2 Strada (Standard and "Street Icons"), MXP Strada, and MXG 1.2 Strada only. Not for original MXS Strada, MXS/MXP/MXG data logging dashes, or any other dash or logger.

AiM Sports AiM OBD Harness for MX-Series 1.2 Strada Dashes $159.99

AiM OBD Harness for MX-Series 1.2 Strada Dashes From AIM Sports, discover the specialized wiring harness compatible with the AiM MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada street dashboards. Designed to seamlessly connect via a 14-pin AMP connector, this harness ensures efficient power, ground, USB, and CAN expansions. Additionally, it facilitates a direct ECU link through the OBD-II diagnostic port. Ideal for production vehicles equipped with an OBD-II port, the harness supports both CAN and K-Line communication standards. Available for individual purchase. Note: Dashboard is sold separately."

Garmin Garmin Remote Camera $159.00

Garmin Remote Camera This is a replacement 1080P camera for the Garmin Catalyst Driver Performance Optimizer. Includes power/data cable, polarized lens cover, adhesive mount and adhesive cable clips. IN THE BOX: Remote cam Polarized lens cover Adhesive mount One 3.5-meter cable Five cable clips

AiM Sports AiM Sports Pressure Sensor $139.00

AiM Sports Pressure Sensor NOTE: Sensors typically take 3 to 5 business days to ship. Add the appropriate AiM Sports Pressure Sensor to your AiM data set-up to retrieve exactly the information you need to maximize your data acquisition and take your racing to the next level! All sensors have a 40 cm (16 inch) cable length

Add to cart

AiM Sports AiM Sports Position Sensors from $135.00

AiM Sports Position Sensors NOTE: Sensors typically take 3 to 5 business days to ship. Add the appropriate AiM Sports Position Sensor to your AiM data set-up to retrieve exactly the information you need to maximize your data acquisition and take your racing to the next level! All sensors have a 30cm (12 inch) cable length

Add to cart

Garmin Garmin Catalyst Screw Down Mounting Kit $129.99

Garmin Catalyst Screw Down Mounting Kit To mount the award winning Garmin Catalyst to a race car, we prefer the Garmin Catalyst Screw Down Mounting Kit. It includes a flat mount plate with two articulating balls and the special magnetic tablet mount. Garmin Catalyst Screw Down Mounting Kit Details: Manufacturer: Garmin Manufacturer Part Number: 010-13081-01 We have many racers that also take their Garmin Catalyst from their track car to their DE car and the Garmin 010-13081-01 Screw Down Mounting Kit is a track worthy way of securing your Catalyst to your race car.

Garmin Garmin Catalyst Cage Mount $129.95

Garmin Catalyst Cage Mount (RAM Mount) For use with the Garmin Catalyst Driver Performance Optimizer. NOTE: This is not a roll cage mount.

Garmin Garmin Catalyst Suction Mount $129.00

Garmin Catalyst Suction Mount For use with the Garmin Catalyst Driver Performance Optimizer.

Find anything you need

Sign Up and Save