Girodisc
A1-127 Girodisc 2pc Front Brake Rotors (OEM PCCB)
$1,700.00
PORSCHE 997 GT2/GT3 (2007-2011) WITH OEM PCCB
The Girodisc system is a direct 380mm replacement for the OE disc on 997.1 GT3/GT2's with OEM PCCB rotors. No modifications are necessary, allows use of factory unmodified pads unlike most aftermarket solutions for this application. The disc will bolt directly to the car and work with OE calipers perfectly. By upgrading your brakes with lightweight high performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency.
The central hat section of our rotor is made from strictly U.S. sourced 6061-T6 aircraft specification aluminum. The disc is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.
The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for a long lasting corrosion resistance. These pins take the load from braking actions while maintaining the axial and radial float between the hat and disc. The pins are secured by class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion but eliminate the rattle and noise associated with floating rotors. This float also allows the rotor to self center between the pads.
Once the Girodisc system is in place, simply replace the cast iron rotor when needed.
Sold/priced in pairs
Girodisc
A2-155 Girodisc 2pc Rear Brake Rotors (OEM Steel)
$1,700.00
Girodisc A2-155 Two Piece Floating Racing Brake Rotors
These Rotors Fit The Following Cars (w/ OEM Steel Rotors):
Porsche 981 Cayman GT4 Rear
Porsche 718 Cayman GT4 Rear
Porsche 991 Turbo/Turbo S Rear
This Girodisc system upgrades your Porsche OEM rear brakes to 380mm two-piece steel discs and aluminum hats. This two-piece floating rotor design will bolt directly to your Porsche GT4 or Turbo and work flawlessly with the OEM calipers using the included machined aluminum spacers. Especially when paired with the Girodisc A1-066 front Porsche rotors , upgrading your brakes to lightweight, high-performance Girodisc rotors, you maintain the factory brake bias and ABS effectiveness. Much lighter than the OEM rotors, Girodisc rotors reduce rotational and unsprung mass giving you stronger braking and faster suspension response.
Combined with Pagid or PFC racing brake pads and Thunderhill Performance RF1 racing brake fluid, Girodisc rotors are the ultimate solution to overheated, cracked OEM Porsche rotors that result from high-performance driving. The central hat of the rotor is made from 6061-T6 aircraft aluminum. The disc is manufactured in the USA from the same cast iron used by professional racing organizations. Its curved-vane design, developed in racing, acts like a centrifugal pump forcing cool air through the disc.
The disc and hat mount together through a floating mount system using ten cadmium plated, high-strength alloy steel drive pins manufactured by Girodisc. These drive pins transfer braking load while maintaining axial and radial float between the disc and hat to allow for heat expansion. Anti-noise spring washers eliminate the noise typically associated with floating rotors.This two-piece Girodisc design allows for disc-only replacement, reusing the hat to minimize maintenance costs.
Sold/priced per pair.
Girodisc
A1-126 Girodisc 2pc Front Brake Rotors (997 GT3 Cup Car)
$1,700.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Porsche 997 GT3 Cup Car
The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight (approx. 8 lbs) allows for quicker acceleration and suspension response.
When used with Pagid or PFC performance brake pads, and Thunderhill RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
A1-174 Girodisc 2pc Front Brake Rotors (Acura NSX)
$1,700.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Acura NSX with OEM CCM Rotors (Conversion to Iron)
The GiroDisc system is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight allows for quicker acceleration and suspension response.
When used with Pagid or PFC performance brake pads, and Thunderhill RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
A1-238 Girodisc 2pc Front Brake Rotors (991 GT3 Cup Car)
$1,700.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Porsche 991 GT3 Cup Car (Front)
The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight (approx. 8 lbs) allows for quicker acceleration and suspension response.
When used with Pagid or PFC performance brake pads, and Thunderhill RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
A2-238 Girodisc 2pc Rear Brake Rotors (991 GT3 Cup Car)
$1,700.00
Thunderhill is an Authorized dealer for GiroDisc products and we are one of the largest stocking dealers in the country. We ship most products same or next business day to ensure we meet your delivery deadline.
Fits Porsche 991 GT3 Cup Car (Rear)
The GiroDisc system is an upgrade to a 2-piece steel rotor and aluminum hat combination and is a direct replacement for the OEM brake disc. The 2-piece floating disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with these lightweight high-performance replacements as opposed to a big brake kit, your factory bias is maintained as well as your ABS efficiency. The Giro Disc rotors are lighter than OEM pieces. The reduction in rotational and unsprung weight (approx. 8 lbs) allows for quicker acceleration and suspension response.
When used with Pagid or PFC performance brake pads, and Thunderhill RF-1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes 8-10 high strength alloy steel drive pins manufactured by GiroDisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by grade12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The 2-piece GiroDisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/Priced per pair.
Girodisc
A1-266 Girodisc 2pc Front Brake Rotors GT4 ClubSport
$1,700.00
This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM GT4 Clubsport steel brakes. The A1-266 will bolt directly to the GT4 ClubSport and work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A1-266 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors originate cracks which can lead to rotor failure. When paired with the Girodisc A2-266 rear rotors, your factory brake bias and ABS efficiency are maintained.
When used with Pagid or PFC performance brake pads, and Thunderhill RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/priced per pair.
Girodisc
A2-266 Girodisc 2pc REAR Brake Rotors GT4 ClubSport
$1,700.00
This Girodisc system is a 380mm two-piece steel rotor and aluminum hat combination, a direct-replacement upgrade for the one-piece OEM GT4 Clubsport steel brakes. The A2-266 will bolt directly to the GT4 ClubSport and work perfectly with your OEM calipers. There are two main reasons for replacing your OEM rotors: first, the Girodisc rotors are designed to shed heat more effectively than the original rotors; second, the slotted Girodisc A2-266 will far outlast the OEM drilled rotors. When subjected to intense heat in a racing or track-day environment, the drilled holes in the OEM rotors originate cracks which can lead to rotor failure. When paired with the Girodisc A1-266 front rotors, your factory brake bias and ABS efficiency are maintained.
When used with Pagid or PFC performance brake pads, and Thunderhill RF1 brake fluid (also available from CompetitionMotorsport.com), you have an amazing solution to overheating, cracking and warping rotors.
The central hat section of the disc is made from 6061-T6 aircraft specification aluminum. The disc is manufactured from cast iron which is constructed in the USA and is made to the same specification with the same material used by professional racing organizations. The rotors curved vane design was developed in racing and acts as a centrifugal pump to force cooling air through the disc.
The rotor and hat mount together through a floating mount system which utilizes eight to ten high strength alloy steel drive pins manufactured by Girodisc in the USA to our own specifications and are cadmium plated for corrosion resistance. The alloy drive pins transfer the load from the brake action while maintaining the axial and radial float between the disc rotor and hat. The pins are secured by Grade 12 cap screws with hardened washers and mounted with anti-noise spring washers to allow for heat expansion while eliminating the rattle and noise associated with floating rotors.
The two-piece Girodisc design allows for rotor only replacement as well to minimize future replacement costs and deliver outstanding performance and cooling.
Sold/priced per pair.
Girodisc
A2-272 Girodisc 2pc Rear Brake Rotors (OEM Steel)
$1,700.00
Girodisc A2-272 Two Piece Floating Racing Brake Rotors
These Rotors Fit The Following Cars (w/ OEM Steel Rotors)
Porsche 992 GT3 Rear
Porsche 992 GT3RS Rear
Porsche 718 GT4RS Rear
The Girodisc system is a direct replacement for the OEM rear discs on the 992 GT3 & GT3RS and the 718 GT4RS with OEM iron rotors. No modifications are necessary, allowing use of unmodified factory pad shapes unlike most aftermarket solutions for this Porsche. The disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with lightweight, high performance replacements -- as opposed to a big brake kit -- your factory brake bias and ABS efficiency are preserved.
The central hat section of our rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The rotor is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.
The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for long-lasting corrosion resistance. These pins take the load from braking while maintaining the axial and radial float between the hat and disc. The pins are secured by Class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion, eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the pads.
Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed. When used with Pagid or PFC racing brake pads and hi-temp Thunderhill Performance RF1 racing brake fluid, you have what amounts to a truly amazing solution to overheating or warping rotors.
If your car came stock with OEM center lock wheels please select the center lock drive pin option.
Sold/priced in pairs.
Girodisc
A1-291 Girodisc 2pc Front Brake Rotors for Porsche 718 GT4RS (OEM Steel)
$1,700.00
Girodisc A1-291 Two Piece Floating Racing Brake Rotors
These Rotors Fit The Following Cars (w/ OEM Steel Rotors)
Porsche 718 GT4RS (Front)
The Girodisc system is a direct replacement for the OEM front discs on the Porsche 718 Cayman GT4RS with OEM iron rotors. No modifications are necessary, allowing use of unmodified factory pad shapes unlike most aftermarket solutions for this Porsche. The disc will bolt directly to the car and work with OEM calipers perfectly. By upgrading your brakes with lightweight, high performance replacements -- as opposed to a big brake kit -- your factory brake bias and ABS efficiency are preserved.
The central hat section of our rotor is made from strictly USA-sourced 6061-T6 aircraft specification aluminum. The rotor is made from Girodisc's own proprietary cast iron, poured in the USA and machined from start to finish in house at Girodisc. The rotor utilizes a curved vane design, developed in racing to act as a centrifugal pump to force cooling air through the disc.
The rotor and hat have a floating mount system, which utilizes 12 high strength alloy steel drive pins, manufactured by Girodisc in the USA to their own specifications and cadmium plated for long-lasting corrosion resistance. These pins take the load from braking while maintaining the axial and radial float between the hat and disc. The pins are secured by Class 12.9 cap screws with hardened washers. In order to keep the rotors from making noise when cold, the pins are mounted with anti-noise spring washers on the rotor side which allow the rotor to grow with heat expansion, eliminating the rattle and noise commonly associated with floating rotors. This float also allows the rotor to self center between the pads.
Once the Girodisc system is in place, simply replace the cast iron rotor ring when needed. When used with Pagid or PFC racing brake pads and hi-temp Thunderhill Performance RF1 racing brake fluid, you have what amounts to a truly amazing solution to overheating or warping rotors.
If your car came stock with OEM center lock wheels please select the center lock drive pin option.
Sold/priced in pairs.
Sparco
Sparco Eagle 2.0 Driver Suit
$1,699.00
Sparco Eagle 2.0 Driver Suit
The Eagle 2.0 is newest evolution of the Eagle suit. The new Eagle 2.0 features an updated, softer HOCOTEX® material which is 30% thinner. The Eagle 2.0 features an all-new design with four new colorways. The Eagle 2.0 carries the newest FIA homologation.
SINGLE LAYER CONSTRUCTION, MULTI-LAYER PERFORMANCE
The Eagle 2.0 is the result of over 3 years of research and development. Sparco has patented a new technology called HOCOTEX® which revolutionizes the way racing suits are made. This new exclusive Sparco technology creates a single layer fabric which has the protection of what is normally achieved by a multi-layer fabric. The Eagle 2.0 is FIA 8856-2018 homologated.
UNPRECEDENTED COMFORT
Thanks to HOCOTEX®, the Eagle 2.0 is three times more breathable than a suit produced using traditional technology. The use of this relatively thinner fabric along with large side and back stretch panels and 360 degree arm gussets give the Eagle 2.0 ultimate flexibility and comfort. The Eagle 2.0 uses at new stretch material called Eagle fabric, which is lighter, more breathable, and more abrasion resistant than traditional stretch material.
IMPROVED FIRE RESISTANCE
Traditional racing suits have layers of fabric sewn together in a quilted pattern. The quilting provides air space between the layers which bloats in a fire, this provides thermal protection to the driver. HOCOTEX® creates a honeycomb structure with internal air cells that ensure the driver even more fire protection. Traditional box quilting creates an average of 300 air chambers in a size 52 suit. The Eagle 2.0 has over 60,000 microcell air chambers which provide a 10 to 12% increase in heat protection performance.
TECHNOLOGY
Single layer construction, multi-layer protection
3X more breathable than a standard suit with full 360o arm gussets
Large stretch panels on sides and back with new breathable fabric
Reinforced arms and legs with anti-abrasive material
Three years of research and development
HOCOTEX® patented Sparco Technology made in Italy
Available in four colorways
FIA 8856-2018 homologated
Sparco
Sparco QRT-C Carbon Racing Seat
$1,699.00
Sparco QRT-C Carbon Racing Seat
The QRT-C is an all-carbon fiber version of the QRT-R. The QRT-C is the lightest “large” size carbon fiber seat on the market. The QRT-C weighs 12.5lbs (with padding and cover) and is constructed from “Pre-Preg” aerospace grade carbon fiber, also known as Dry Carbon. The QRT-C was specifically designed for a large driver and it fits up to a 36” waist driver comfortably. The QRT-C is unique because it was designed to fit a larger driver but has excellent fitment into smaller cockpits The QRT-C requires the special QRT Side Mounts (#600QRT) which allows the seat to be racked back for a comfortable seating position. The QRT-C is FIA approved.
SIZING
Large – up to a 36” waist (pants size)
WHAT IS QRT?
Designed and developed at the Sparco OEM Composite Laboratory in Italy, QRT is a patented state-of-the-art technical process, based on aerospace technologies.
QRT creates an unparalleled mechanical strength-to-weight ratio. This innovative production method generates the lightest fiberglass composite seat shells currently on the market; in fact, it guarantees a reduction in total weight of up to 30% compared to traditional production methods. The QRT seats approach the weight of a comparable carbon fiber seat at a lower price point.
TECHNOLOGY
Ultralight Carbon Fiber - 12.5lbs fully trimmed weight
Excellent fitment into small cockpits
Large size driver fitment
Excellent ergonomics
Fire retardant fabric
Special non-slip fabric
FIA approved
QRT-C CARBON DIMENSIONS
Sparco
Sparco QRT-K Carbon Kevlar Racing Seat
$1,699.00
Sparco QRT-K Carbon Kevlar Racing Seat
The QRT-K is a full Carbon Kevlar version of the QRT-R. The QRT-K looks amazing with the exposed yellow/black Carbon Kevlar weave. The QRT-K is one of the lightest seats on the market. The QRT-K weighs 13.5lbs fully trimmed (with padding, cover and harness guides) and is constructed from “Pre-Preg” aerospace grade Carbon Kevlar. The QRT-K was specifically designed for a larger driver and it can fit a 36” waist (pants size) driver. The QRT-K is unique because it was designed to fit a larger driver but has excellent fitment into smaller cockpits. The QRT-K requires the special QRT Side mounts (#600QRT) which allows the seat to be raked back for a comfortable ergonomic seating position. The QRT-K is FIA approved.
SIZING
Large fits up to a 36” waist (pants size)
WHAT IS QRT?
Designed and developed at the Sparco OEM Composite Laboratory in Italy, QRT is a patented state-of-the-art technical process, based on aerospace technologies.
QRT creates an unparalleled mechanical strength-to-weight ratio. This innovative production method generates the lightest fiberglass composite seat shells currently on the market; in fact, it guarantees a reduction in total weight of up to 30% compared to traditional production methods. The QRT seats approach the weight of a comparable carbon fiber seat at a lower price point.
TECHNOLOGY
Ultralight Carbon Kevlar Composite Shell - 13.5lbs including cover and padding
Visible carbon kevlar weave
Excellent fitment into small cockpits
Large size driver fitment
Excellent ergonomics
Fire retardant fabric
Special non-slip fabric
FIA approved
QRT-K CARBON KEVLAR DIMENSIONS
Sparco
Sparco Superleggera Race Suit
$1,699.00
Sparco Superleggera Race Suit
The Sparco Superleggera race suit is the lightest FIA 8856-2018 approved suit on the market. The Superleggera is not only lightweight but it is also one of the most comfortable Sparco race suits available. It features a special 4-way stretch panel that runs from the underarm down to the hip. Those side stretch panels combined with the rear stretch panel give ultimate mobility when in the seated positions. The Sparco Superleggera fire resistant auto race suit also has a breathable inner thigh stretch panel, 360 floating arm gussets and pre-curved arms and legs. The Sparco Superleggera auto race suit is FIA and SFI homologated.
SPARCO SUPERLEGGERA RACE SUIT TECHNOLOGY
FIA 8856-2018 and SFI 3.2A/5 Approved
Lightest FIA suit on the market
Pre-curved Arms and Legs
Lightweight zipper and collar
Inner Thigh Stretch Panel
4-Way Stretch Panels
Sparco
Sparco EVO Carbon Fiber (STD, L, XL) Racing Seat
$1,699.00
Sparco EVO Carbon Fiber Racing Seats
As Sparco's most well known competition seat, it was a no-brainer to provide the refreshed Evo with Sparco's QRT Ultra-Light Technology. Not content to leave well enough alone, Sparco went a step further by improving the overall fit and feel of the Sparco Evo Carbon Fiber. Starting with the shoulder bolsters, Sparco trimmed down the width to help fitment into smaller cars without sacrificing support. Sparco then lowered the side bolsters just enough to improve ingress/egress into/out of the car. Finally, the shoulder belt guides have been raised for improved harness fit in all drivers. With small sports cars in mind (the Sparco Evo Carbon Fiber fits perfectly in a Miata!), the Sparco Evo Carbon Fiber is sure be a mainstay at the track!
The EVO Carbon is the all-carbon fiber version of the EVO QRT. It is constructed with “Pre-Preg” aerospace grade carbon fiber, also known as Dry Carbon. EVO Carbon is one of the lightest carbon fiber seats on the market. It weighs less than 10lbs (shell only) and 12lbs (with padding and cover). The EVO Carbon is has excellent fitment into smaller cockpits. The EVO series of seats feature the most back angle rake of all Sparco seats for a very comfortable driving position. It also has high grip material in strategic places such as the shoulder bolsters and seat bottom to aid in lateral support. The EVO Carbon is FIA 8859-1999 approved. SIZINGEVO CARBON – Medium (up to 34” waist)EVO L CARBON – Large (up to 36” waist)EVO XL CARBON – X-Large (38” waist)
The
Sparco EVO QRT Racing Seat TECHNOLOGY
Ultralight Pre-Preg Carbon Fiber shellExcellent fitment into small vehicle cockpits3 Sizes: Medium through XLExcellent ergonomicsFire retardant fabricSpecial non-slip fabricFIA 8859-1999 approved
The Sparco EVO CARBON FIBER Racing Seat SIZING
The Sparco EVO series is among the most versatile competition seats we carry, available in the following four sizes to ensure proper fitment:
EVO 008007ZNR – Medium (up to 34” waist)
EVO L 008013ZNR – Large (up to 36” waist)
EVO XL 008015ZNR – Extra Large (38” waist)
The Sparco EVO Carbon Fiber Racing Seat DIMENSIONS
EVO Std Dimensions:
EVO L / XL Dimensions:
CMS Performance
CMS Performance Roll Bar for Shelby GT350/GT350R/GT500
$1,695.00
CMS Performance Roll Bar for Shelby GT350, GT350R, GT500
This Roll Bar Fits The Following Cars:
Ford Shelby GT350 (2016-2020)
Ford Shelby GT350R (2017-2020)
Ford Shelby GT500 (2015+)
The Best Roll Bar On Earth for Ford's Track Day Monsters
The CMS Performance Roll Bar is the strongest, safest, and most beautifully constructed roll bar on the market for the Shelby GT350, GT350R, and GT500. In designing our Shelby roll bar, safety, strength, and structural integrity were our primary goals. That's why it is fully TIG welded from ultra-strong Docol R8 Advanced High-Strength Steel sized 1.75" diam x .095" wall, vs. the mild-steel tubing other companies use. Docol R8 is 30-35% stronger than DOM mild steel and even 10-15% stronger than 4130 CrMo steel. This allows CMS Performance to design a roll bar that is stronger and lighter weight.
Precision CNC machined interlocking roll bar clamps, made to our specifications in the USA, make joining the main hoop and kickers easier during installation while giving the CMS Performance roll bar a premium, finished look. Adding an optional Shrader Rear Seat Delete Kit (not necessary on the GT350R) gives your roll bar installation a from-the-factory OEM look.
American Made Safety for an American Icon
Let's face it, safety is the primary reason to install a roll bar in your Shelby. So the CMS Performance Shelby Roll Bar is designed to place your harness shoulder straps at both the proper angle (0° to -20°) and distance to the driver. The rear kickers bolt to a strong existing bulkhead, requiring no reinforcement plates beneath the floor pan. Our use of state-of-the-art Docol ultra-high-strength-steel tubing throughout allows us to keep the driver's rear view unobstructed by diagonal braces, which also keeps weight down. Every detail is engineered with safety and structural integrity as our primary goal.
Precision Crafted and Custom Finished in OEM Colors
The other reason to install a roll bar is because it really complements the aggressive, race-inspired styling of the Shelby S550 and Shelby GT350/R/500. We're gear heads, we get that. So each bar is crafted by hand by master fabricators, 360o TIG welded for the ultimate in strength and durability, and then custom powder coated in our facility (at no extra charge). We've color-matched powder to most of Ford's factory paint colors for a truly customized look, or you can choose from thousands of custom colors and finishes like the amazing Superchrome, giving your Shelby a personalized look that will last. Going from raw Docol tube stock to a gleaming finish, every roll bar is handcrafted by our most experienced cage- and race car builders. Nothing is left to chance.
The CMS roll bar is designed to give you an unobstructed view through your rear window. None of your plastic interior trim needs to be removed or cut, just a little carpet that is hidden away. So if you ever need to put your car back to stock, it will look as though the roll bar was never there.
Easier Installation and Lots of Options for Your Shelby Roll Bar
Check out the GREAT installation video here! 1
Complete, detailed instructions make installation pretty simple (figure about two hours if you're reasonably handy; having a buddy helps!) All the supplied installation hardware is American made: Grade 8 mounting hardware and an industrial carbide drill bit. So you don't have worry that you don't have what you need for a flawless installation.
You can add six-point or four-point harnesses to your order to take full advantage of the safety upgrade your roll bar represents. The CMS Performance Sub Strap + Lap Belt Mount makes securely installing your racing harnesses easy. Check out the drop-downs above.
Many customers also add CMS Locking Harness Collars to keep harness shoulder straps right where you want them (they're not required for safety, but a lot of people like the look.)
1 Thanks so much to our customer "@1_trickpony_" for putting in the time and effort to shoot and edit a fantastic installation video!
Click Here For Installation Instructions
CMS Performance Shelby/Shelby Roll Bar Details:
Manufacturer: CMS Performance
Manufacturer part no.: RB03
Material: 1.75″ x .095" Docol R8 Advanced High-Strength Steel tubing
Construction: full 360o TIG welding
Design: one-piece main hoop and three-piece rear kicker for simpler installation.
Weight: 52 lbs. (23.6 kg)
Included hardware: all necessary Grade 8 bolts, nuts & washers
Drill bit: included
CMS Performance Roll Bar Features:
CNC-cut mounting plates.
Designed, built, and finished by CMS Performance in the USA.
American-made CNC machined high-strength steel interlocking clamps
Allows full seat travel with any seat.
Straightforward installation and perfect fitment, guaranteed.
This product is intended for off-road race track use only.
Sign Up and Save
Subscribe to our eNewsletter to learn about events near you, great deals, new products and for tips to improve your creator skills.
